![]() Perform configuration backup and restore.Discover Smart Managed Switches in your network.It allows you to perform the following tasks. The NETGEAR Smart Control Center (SCC) is a Windows-based application. What is the Smart Control Center utility? Currently tested and supported Browsers:ġ2.What are the current supported host OS and Web browsers for XS728T? Up to 32 routing VLANs and up to 64 static routes (IPv4, IPv6 respectively) are supported.ġ1. The XS728T supports IPv4/IPv6 static routing, which can help build a 元 connection with other switches or offload router for WAN traffic only. What routing features are supported on the XS728T, and what can they be used for? The XS728T supports IPv6 Management, IPv6 MLD Snooping, IPv6 ACL, IPv6 QoS and IPv6 Static Routing.ġ0. What IPv6 functions are supported on the XS728T? When EEE Mode is enabled on a port, the port will work in an Energy Efficiency mode that fully conforms to the standard of IEEE 802.3az (EEE).ĩ.When Short Cable Mode is enabled, the device will check the cable length and reduce the output power if the cable length is less than 30 meters.When Sleep Mode is enabled on a port, the port will automatically enter a lower power mode if there is no link.The XS728T supports Sleep Mode, Short Cable Mode and EEE Mode on copper ports. What Green Ethernet Features are supported by the XS728T? No, the XS728T switches only support firmware 6.5.0.x.Ĩ. Does the XS728T use the same firmware as the XS712T? THE SERIAL PORT IS NOT FOR CUSTOMER USE.ħ. The serial port is for debugging purposes only which might be requested by NETGEAR support. What can the serial port on the back panel be used for? The USB device must be formatted with FAT32 file system type.This device attached to the USB port must comply with the following requirements: The XS728T provides one USB port that can be used to upgrade the firmware and backup the configuration using a supported USB storage device. What is the USB port on the XS728T used for? ![]() The XS728T can connect with all NETGEAR switches that provide 10G ports (the current list is shown below). Which NETGEAR switches can be connected with the XS728T for 10G end-to-end connectivity? Please check with the manufacturer for compatibility prior to purchasing such modules.Ĥ. Cisco SFP-10G-SR, Finisar FTLX8571D3BCL, Delta LCP-10G3A4EDR-G, Cisco SFP-10G-LR, Finisar FTLX1471D3BCL, Delta LCP-10G3B4QDR-G Cisco MGBLX1, Finisar FTRJ1319P1BTL, Cisco MGBSX1 IEEE 802.3z (1GBASE-LX and 1GBASE-SX) E.g.Here are some supported examples from 3rd party vendors. SFP/SFP+ optical modules from 3rd party vendors are also supported if they comply with below standards. NETGEAR offers a complete line of both SFP and SFP+ modules designed for this switch including: AGM731F, AGM732F, AGM734, AXM761, AXM762, AXC761 and AXC763. The XS728T comes with 4 SFP MSA sockets that can be used with either one Gigabit SFP or 10-Gigabit SFP+ optical modules. Which optical modules do the SFP+ ports support? Note that CAT 6a or CAT 7 cables are recommended to make 10G connections if cable distance is greater than 45 m (148 ft).ģ. ![]() Both UTP (Unshielded Twisted Pair) and STP (Shielded Twisted Pair) cables are supported. What cables can be used with the 10G copper ports on the XS728T?Ĭategory 5e (CAT 5e) or better Ethernet cable (CAT 6, CAT 6a, or CAT 7) terminated with an RJ-45 connector can be used to make 10-Gigabit connections on copper ports. New GUI style that supports the most popular WEB Browsers (see Question 11 below for a complete list)Ģ.One USB port for firmware upgrade and configuration backup. ![]() What are the major enhancements for the XS728T compared with the XS712T? It supports 24 copper 10GBased-T ports and four dedicated 1G/10G fiber ports.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |